Software/axiom: Difference between revisions
From National Optronics resources center
Jump to navigationJump to search
No edit summary |
No edit summary |
||
| Line 27: | Line 27: | ||
=== New features === | === New features === | ||
=== Bugs fixed === | === Bugs fixed === | ||
* Passe size | |||
* PT update time changed from 60 to 15 | |||
* New tangent algorithm | |||
* New PID values | |||
* Chuck protection reduce for lenses | |||
* Calibration Wizard requires better precision on lens curve | |||
* Internet server IP address updated. | |||
* Bug#563: Sag gauge range | |||
* Bug#615: Label "base curve" replaced by "sag value" | |||
* Bug#009: Cutter algorithm position error for high curve | |||
* Bug#262: We need to be able to cut wax | |||
* Bug#271: When cutting flat curves (near plano) a lip can be present around the outer edge of the lens | |||
* Bug#567: Laps with high cylinder are showing flat and with propellar marks | |||
* Bug#582: The pin bevel applied is not flat and is inconsistent | |||
* Bug#585: Surface finish on laps not comparable to 2G | |||
* Bug#614: One lens job screen, base,cross and back curve are by default negative. | |||
* Bug#287: Lap calibration use it own cycle speed | |||
=== Download === | === Download === | ||
* Axiom USB software update [http://nationaloptronics.net/download/Axiom/software/AxiomUpdateUSB%201.04.08.exe (download)] | * Axiom USB software update [http://nationaloptronics.net/download/Axiom/software/AxiomUpdateUSB%201.04.08.exe (download)] | ||
* Axiom finger print generator [http://nationaloptronics.net/download/Axiom/software/Axiom%20fingerprint%20V1.00.exe (download)] | * Axiom finger print generator [http://nationaloptronics.net/download/Axiom/software/Axiom%20fingerprint%20V1.00.exe (download)] | ||
Revision as of 13:28, 9 May 2011
Version 1.04 RC
New features
- Can backup DCS log on external thumb drive.
- Can send DCS log over Internet.
- If clear Job number machine than use internal tool and prism index.
- Automatically save/restore config files using FingerPrint and DiskOnModule.
- Check machine parameters and job data are valid before starting a cycle.
- Multi-languages implemented.
- Can use or ignore OMA block data.
- Checks block data before starting a cycle.
Bugs fixed
- Bug#438 After pulling up a new job the screen switch to the Lens screen.
- Bug#186 Not a bug.
- Bug#192 Need red message when an error occurs.
- Bug#019 Can change serial port speed.
- Bug#189 USB driver crash (not fixed: use new thumb drive)
- Bug#438 Go to lens screen after downloading a job.
- Bug#422 Use IFRNT if valid; if else use FRNT.
- Bug#007 Use tool index and prism index to generate lens curve.
Download
- Axiom USB software update (download)
- Axiom finger print generator (download)
Version 1.04.08 beta
New features
Bugs fixed
- Passe size
- PT update time changed from 60 to 15
- New tangent algorithm
- New PID values
- Chuck protection reduce for lenses
- Calibration Wizard requires better precision on lens curve
- Internet server IP address updated.
- Bug#563: Sag gauge range
- Bug#615: Label "base curve" replaced by "sag value"
- Bug#009: Cutter algorithm position error for high curve
- Bug#262: We need to be able to cut wax
- Bug#271: When cutting flat curves (near plano) a lip can be present around the outer edge of the lens
- Bug#567: Laps with high cylinder are showing flat and with propellar marks
- Bug#582: The pin bevel applied is not flat and is inconsistent
- Bug#585: Surface finish on laps not comparable to 2G
- Bug#614: One lens job screen, base,cross and back curve are by default negative.
- Bug#287: Lap calibration use it own cycle speed
Download
- Axiom USB software update (download)
- Axiom finger print generator (download)
