4T: Difference between revisions
From National Optronics resources center
Jump to navigationJump to search
| Line 10: | Line 10: | ||
* [http://nationaloptronics.net/download/4T/manual/4TxES-traceEnglishManualInsertRev1.01.pdf 4TX / ES-Trace User Manual] | * [http://nationaloptronics.net/download/4T/manual/4TxES-traceEnglishManualInsertRev1.01.pdf 4TX / ES-Trace User Manual] | ||
* [http://nationaloptronics.net/download/4T/manual/4TxES-traceFrenchManualInsertRev1.01.pdf Manuel d'utilisation 4TX/ES-Trace] | * [http://nationaloptronics.net/download/4T/manual/4TxES-traceFrenchManualInsertRev1.01.pdf Manuel d'utilisation 4TX / ES-Trace] | ||
* [http://nationaloptronics.net/download/4T/manual/4TxES-traceSpanishManualInsertRev1.01.pdf Manual de uso del 4TX/ES-Trace] | * [http://nationaloptronics.net/download/4T/manual/4TxES-traceSpanishManualInsertRev1.01.pdf Manual de uso del 4TX / ES-Trace] | ||
* [http://nationaloptronics.net/download/4T/manual/4Ti-German-Manual-Insert-Rev1.02.pdf 4Ti Bedienungsanleitung] | * [http://nationaloptronics.net/download/4T/manual/4Ti-German-Manual-Insert-Rev1.02.pdf 4Ti Bedienungsanleitung] | ||
* [http://nationaloptronics.net/download/4T/manual/4Ti-Italian-Manual-Insert-Rev1.02.pdf Manuale Operatore Del Lettore 4Ti] | * [http://nationaloptronics.net/download/4T/manual/4Ti-Italian-Manual-Insert-Rev1.02.pdf Manuale Operatore Del Lettore 4Ti] | ||
Revision as of 13:13, 24 September 2013
Documentation
Manuals
- 4T
- 4TX / ES-Trace
- 4TX / ES-Trace User Manual
- Manuel d'utilisation 4TX / ES-Trace
- Manual de uso del 4TX / ES-Trace
- 4Ti Bedienungsanleitung
- Manuale Operatore Del Lettore 4Ti
- Manual do Usuário do 4Ti
Technical information
- Replacement of Software Chips for Software Update - 1st style 4T/4Ti main board
- 4T Troubleshooting Guide
4Ti Software
Version 2.01
- New features
- Support the cycle burn-in function.
- Arc-net largely disabled. Most functions immediately return or are commented out.
- Implementation of servo test function for R. Wesner
- Frame trace burn-in with statistics is provided and the compile switch governing whether frame bevel calibration is 1-eye or 2-eye is set to 2-eye.
- Improved algorithm for std deviation during burn-in
- Bugs fixed
- (none)
- Regression
- Remove RESET soft-key on servo test screen. (Servo test not generally enabled.)
- Download (WARNING - 4Ti product only!!!)
- Binary files #0 for 4Ti(download bin0)
- Binary files #1 for 4Ti(download bin1)
Version 2.00
- New features
- Driver for new Xilinx controller
- Driver for new memory chips
- Bugs fixed
- (none)
- Download (WARNING - 4Ti product only!!!)
- Binary files #0 for 4Ti(download bin0)
- Binary files #1 for 4Ti(download bin1)
4T Software
Version 1.35
- New features
- The DCS parameters FCRV and BEVC are both transmitted with job data (with the same value). Some hosts and edgers tend to use FCRV while other devices use BEVC.
- The capability to update the code via the serial port is supported. See note #2 in “Other” below.
- A and B offsets may now be specified for frames, patterns/rimless lenses, and beveled lenses. Total range of available offsets is now A, B, CIRC, and DBL.
- Default values for the left/right carriage servo gains now match the defaults on the tuning sheet.
- Bugs fixed
- The C3/C2 correction to A and B size was applied to all frames, even those that are not high-wrap.
- The FCRV was not computed independantly of the frame faceform wrap.
- Download (WARNING - 4T product only!!!)
- Floppy disk installer (download)
