4T: Difference between revisions
From National Optronics resources center
Jump to navigationJump to search
| Line 43: | Line 43: | ||
=4Ti Software= | =4Ti Software= | ||
== Version 2.01 == | |||
;New features | |||
* Support the cycle burn-in function. | |||
* Arc-net largely disabled. Most functions immediately return or are commented out. | |||
* Implementation of servo test function for R. Wesner | |||
* Frame trace burn-in with statistics is provided and the compile switch governing whether frame bevel calibration is 1-eye or 2-eye is set to 2-eye. | |||
* Improved algorithm for std deviation during burn-in | |||
;Bugs fixed | |||
* (none) | |||
;Regression: | |||
* Remove RESET soft-key on servo test screen. (Servo test not generally enabled.) | |||
;Download (WARNING - 4Ti product only!!!) | |||
*Binary files #0 for 4Ti[http://nationaloptronics.net/download/4T/software/4T-V2.01.BN0 (download bin0)] | |||
*Binary files #1 for 4Ti[http://nationaloptronics.net/download/4T/software/4T-V2.01.BN1 (download bin1)] | |||
== Version 2.00 == | == Version 2.00 == | ||
;New features | ;New features | ||
| Line 50: | Line 66: | ||
* (none) | * (none) | ||
;Download (WARNING - 4Ti product only!!!) | ;Download (WARNING - 4Ti product only!!!) | ||
*Binary files for 4Ti[http://nationaloptronics.net/download/4T/software/. | *Binary files #0 for 4Ti[http://nationaloptronics.net/download/4T/software/4T-V2.00.BN0 (download bin0)] | ||
*Binary files #1 for 4Ti[http://nationaloptronics.net/download/4T/software/4T-V2.00.BN1 (download bin1)] | |||
Revision as of 22:27, 5 July 2012
Documentation
Manuals
- 4T
- 4Ti
Technical information
4T Software
Version 1.35
- New features
- The DCS parameters FCRV and BEVC are both transmitted with job data (with the same value). Some hosts and edgers tend to use FCRV while other devices use BEVC.
- The capability to update the code via the serial port is supported. See note #2 in “Other” below.
- A and B offsets may now be specified for frames, patterns/rimless lenses, and beveled lenses. Total range of available offsets is now A, B, CIRC, and DBL.
- Default values for the left/right carriage servo gains now match the defaults on the tuning sheet.
- Bugs fixed
- The C3/C2 correction to A and B size was applied to all frames, even those that are not high-wrap.
- The FCRV was not computed independantly of the frame faceform wrap.
- Download (WARNING - 4T product only!!!)
- Floppy disk installer (download)
4Ti Software
Version 2.01
- New features
- Support the cycle burn-in function.
- Arc-net largely disabled. Most functions immediately return or are commented out.
- Implementation of servo test function for R. Wesner
- Frame trace burn-in with statistics is provided and the compile switch governing whether frame bevel calibration is 1-eye or 2-eye is set to 2-eye.
- Improved algorithm for std deviation during burn-in
- Bugs fixed
- (none)
- Regression
- Remove RESET soft-key on servo test screen. (Servo test not generally enabled.)
- Download (WARNING - 4Ti product only!!!)
- Binary files #0 for 4Ti(download bin0)
- Binary files #1 for 4Ti(download bin1)
Version 2.00
- New features
- Driver for new Xilinx controller
- Driver for new memory chips
- Bugs fixed
- (none)
- Download (WARNING - 4Ti product only!!!)
- Binary files #0 for 4Ti(download bin0)
- Binary files #1 for 4Ti(download bin1)
